PE4KH Amateur radio - Koos van den Hout

Most recent QSO's for PE4KH

Callsign Band Mode Locator RST(R) RST(S)
LY5P20MFT8KO15-16-08
2E0DZC20MFT8IO94-11-03
R18TUN20MFT8KN95-16+00
F5HPY20MFT8IN96-02+01
IV3VJH20MFT8JN65-14-15
UA1QDZ20MFT8KO99-07-15
HB0HF20MFT8JN47-01-03
IW1FWB10MFT8JN44-16-17
IU6HWW10MFT8JN63-05-19
OZ2ABI20MFT8JO46-07-03
HB9WDF20MFT8JN47-11-07
MM0JTV10MSSBIO75TS5958
OZ1AHV10MFT8JO55+04-04
EA1ABT10MFT8IN73-05-16
IK7XNF10MFT8JN81+02+08

I passed my novice radio amateur exam in March 2013 and I registered the callsign PD4KH (pappa delta four kilo hotel!). I passed my full radio amateur exam in March 2016 and I registered the callsign PE4KH (pappa echo four kilo hotel!).
PE4KH on qrz.com
PE4KH on hamqth.com

I am usually located around maidenhead locator: JO22NC

The 'hamradio' items from my homepage

2018-05-07 I participated in the ARI International DX Contest
Last weekend I participated in the ARI International DX Contest.

Before the contest I was looking at the option of trying the tlf contest software and operating phone (voice) but adding the definitions for scoring this contest to tlf turned out to be not possible at the moment and at the end the weekend was filled with enough other things that only a few hours of operating RTTY were left. Propagation wasn't very cooperative and I first was blaming local interference until I noticed that the same lack of signals was showing in other places and twitter was filled with aurora pictures, so a solar flare had blocked propagation.

In the end I made 43 contacts and entered in the 'single operator RTTY low power' category. Low power on an Italian scale: below 100 watts.

2018-05-01 Getting amateur satellite contacts into LoTW correctly
A very good bit of info just flew by on the amsat-bb mailing list: Logging Satellite QSOs with Logbook of the World - AMSAT-NA.

Complete with screenshots and needed steps, how to create an ADIF file (which I could import into CQRLOG) with the satellite-specific fields set to the values needed by LoTW to make it a valid satellite-contact.

CQRLOG has no support for satellite-specific contact information, so for me the workflow for these contacts would be to create an ADIF file as above in LoTW, upload it, and import the ADIF file in CQRLOG and not upload it from CQRLOG.

Now to find time, energy and nice weather to get on the satellites again.

2018-04-26 More radio maps and their limits
The PE4KH website has maps of the locations where I contacted radio amateurs all over the world. The maps with generated images are created by exporting my locators worked/confirmed from cqrlog and using gcmwin for linux with a whole set of different configurations to plot the results.

But now the 2 meter band has been added and on that band a 'record distance' is not as far as on HF. On HF my current distance record was a contact with Australia at 16581 kilometers. My current distance record on the 2 meter band is 363 kilometer in Germany. Quite a different scale!

So the maps part has been enhanced with a 2 meter contacts map, but gcmwin can't use 6-position maidenhead locators so the map is quite coarse compared to what I want. I don't know the solution at the moment to improve this. The recent qso map PE4KH does show the more precise gridsquares when available in the log, so maybe that page needs distances added.

2018-04-24 Building my own balun, part 7: Better measurements of the result
Homemade balun version 2 SWR scan 1-60 MHz
Homemade balun version 2 SWR scan 1-60 MHz 20180424
Homemade balun version 2 SWR scan 10 meter band
Homemade balun version 2 SWR scan 10 meter band 20180424
Homemade balun version 2 SWR scan 20 meter band
Homemade balun version 2 SWR scan 20 meter band 20180424
Time to do measurements of the revised attic antenna. And now with a voltage balun with more windings the balun is working better, showing ok SWR values. A nice optimum in the middle of the 20 meter band (although I originally wanted that optimum near the digital mode part) and a nice optimum in the 10 meter band (also somewhat higher than originally planned). Comparing them to the original measurements show an increase in frequency in both SWR curves.

So I consider this a good result! Time to get it on the air and make contacts again.

Next step, working on an outside dipole with the Fritzel balun.

2018-04-23 Building my own balun, part 6: Redo and some success: a working antenna again
After the previous measurements showed the balun and dipole under the roof weren't acting as a perfect combination. So time to do a few things better: more windings, less leftover wire and a switch to a voltage balun. Yes, other sources indicate a current balun is better, but I decided otherwise. The Fritzel balun turned out to be a voltage balun after I removed it from the dipole antenna.

Balun project version 2 in case So I used the instructions at 1:1 voltage balun by VK6YSF to rebuild it as a voltage balun and I made sure the wires were shorter in the end. Getting the shorter wires in the right places in the case did get me some slightly burned fingers!

Success is currently defined as "I can transmit a carrier on the 20 meter or 10 meter band and the SWR meter of my radio only goes up a few segments" which isn't very scientific, I will need to do the rest of the measurements with the SWR meter to be sure.

2018-04-16 Building my own balun, part 5: First tests of the result
Homemade balun SWR scan 1-60 MHz
Homemade balun SWR scan 1-60 MHz 20180415
Homemade balun SWR scan 10 meter band
Homemade balun SWR scan 10 meter band 20180415
Homemade balun SWR scan 20 meter band
Homemade balun SWR scan 20 meter band 20180415
So I removed the old balun and installed the one I made. Removing the old one wasn't easy: the Fritzel balun has a cover over the SO239 connector which makes the heavy duty connector I used very hard to unscrew. So I had to break bits of that cover to get the needed access. And the connector ended with a lot more scratches from my attempts to get access to it.

But now the balun is replaced, and measured. And it looks like some things have changed now causing the antenna to be 'mistuned'.

Update: Just some measurements and thinking: adding the big common mode choke in the mix makes the combination show better SWR curves (still not what I want) but with the frequency with the best SWR still too low. This suggests (to me) two things: I need more windings on the ferrite core and less extra wire length from the core to the connectors. Time for a rebuild.

2018-04-15 Building my own balun, part 4: Deciding on where to put dipole ends and finishing it
Balun, case and ferrite core Balun in open case I finally decided where to put the holes in the case for the dipole ends of the balun. This took some serious pondering!

I made those holes, put screws through them and wound the ferrite core with enamelled copper wire. To guess the needed length of wire I first wound it with packing rope, made a small knot at the point where it was enough and unwound the rope to measure the length I used and took a bit longer wire.

Using sanding paper I removed the enamel isolation from the ends of the wires and used soldering tin on it.

Other parts of this project:

2018-04-08 I participated in the EA RTTY Contest 2018
As planned I participated in the EA RTTY Contest edition 2018.

I had most of the time to play radio on Sunday so I decided to participate in the SO20DX (single operator 20 meter band outside Spain) category. I did make two contacts on the 40 meter band when I thought I wasn't going to find any new station the 20 meter band but I returned. And found more stations on the 20 meter band.

20 meter interference pattern
Interference pattern on the 20 meter band
Radio propagation was ok, best DX were some Asiatic Russia stations and a US station in Illinois. The local noise was bad and there were some new sources of interference active. The pattern as in the image (links to full view of the 2.5 kHz waterfall) which is very stable in frequency and has a tendency to stop and start, and at the stop the carriers move together. Also a more 'rattling' noise which sounded like an electrical problem.

In the end I made 81 contacts in total, 79 on the 20 meter band.

2018-04-06 And a contact with South Africa, new country
Another new country that should not be too hard to get in the log but did not happen until today: South Africa. ZS6ZA was active on 40 meter FT8 and received my answers.

2018-04-04 I am planning to participate in the EA RTTY Contest
After my participation in the EA PSK63 Contest 2018 I plan to have the radio active in the upcoming weekend for the EA RTTY Contest.

Items before 2018-04-04
This page is created by Koos van den Hout, contact information at the end of my homepage.
Other webprojects: Weatherstation Utrecht Overvecht, Camp Wireless, wireless Internet access at campsites The Virtual Bookcase book reviews,
This page generated by $Id$ in 0.035181 seconds.